Welcome to the Home of
Daihatsu Oceania & Compact Motorsport
Daihatsu Parts Distributor and Specialist in Automotive Engineering Design
Daihatsu DM950 technical notes
Handy reference data for owners and workshops running Daihatsu DM950 engines (also sold as Briggs & Stratton 950 diesels). Figures are for the DM950D, DT and DTH unless noted. Always follow good workshop practice, and if in doubt, ask us.
Don't overfill the oil
This is the most important thing to know about these engines. Too much oil – or oil poured in too fast – can be pushed through the crankcase breather into the intake. The engine can then hydraulic-lock, which can bend or break a connecting rod. Damage caused by overfilling isn't covered by warranty.
To fill correctly:
1. Park the engine level.
2. Pull the dipstick out so air can escape, and add oil slowly.
3. Fill to the F mark – no higher. (About 3.3 L with a new filter, 3.1 L for oil only.)
4. Run at idle for 5 minutes, stop, and wait 3 minutes.
5. Recheck with the dipstick pushed fully home. Top up or drain back to F.
Later engines have a "Do not overfill" caution label and a revised dipstick with clear Full and Low holes.
Working on a slope: Daihatsu testing found the engine runs without problems up to 30°. Between 30° and 35° there is a risk of oil getting into the intake depending on the oil level, and beyond 35° the risk is there at any level. Keep continuous operation at 30° or less – and never overfill.
Service intervals
Check oil level, coolant and look for leaks — Daily
Engine oil — First change at 50 h, then every 100 h (at least yearly)
Oil filter — First change at 50 h, then every 200 h
Fan belt — Check every 100 h (about 10–12 mm deflection)
Air cleaner — Clean first at 50 h, then every 100 h; replace every 600 h
Battery — Check every 200 h
Head bolt torque and valve clearance — Check every 600 h
Fuel filter — Replace every 800 h
Coolant — Replace yearly
Service more often in dusty, hot or heavily loaded work. Our service filter kit has the oil, fuel and air filters in one pack: https://www.compactmotorsport.com/product-page/daihatsu-dm950-service-filter-kit-oil-fuel-air-cm-ind-011
Tips: fit the oil filter hand-tight plus ½–¾ turn; fit the fuel filter hand-tight plus about ⅓ turn and bleed the fuel system afterwards. Drain water from the fuel filter if the warning light comes on.
Temperatures
- Normal coolant temperature on the gauge is about 80–90 °C. Thermostat opens at 82 °C.
- Maximum coolant temperature is 105 °C at the outlet. If it gets that hot, let the engine idle to cool, then stop and find the cause.
- Maximum oil temperature in the sump is 125 °C.
Valve clearance
Set with the engine cold: 0.20 mm inlet and exhaust.
1. Turn the crankshaft until the pulley timing mark lines up with the pointer on the timing cover. If both No. 1 valves are loose, No. 1 is at TDC on compression; if not, turn one more full turn.
2. Adjust: inlet valves on cylinders 1 and 3, exhaust valves on cylinders 1 and 2.
3. Turn the crankshaft one full turn (360°) and adjust inlet 2 and exhaust 3.
4. Tighten the adjuster lock nuts to 11 Nm. Refit the valve cover with a new seal seated in its groove (6–7 Nm).
No. 1 cylinder is at the front (pulley end).
Torque settings (Nm)
Head bolts – 8 mm (early): 34; Main bearing caps: 58
Head bolts – 9 mm (DM950D): 43; Con-rod nuts: 36
Head bolts – 10 mm (DT/DTH): 68; Flywheel: 47
Rocker assembly nuts: 19; Crankshaft pulley: 88
Adjuster lock nuts: 11; Camshaft gear: 41
Valve cover: 6–7; Idler gear: 25
Injector nozzle holders: 61; Injection pump drive gear: 61
Glow plugs: 17; Injection pump mounting nuts: 19
Fuel delivery lines: 25; Pump distributor head screw: 17
Fuel return line: 27; Oil drain plug: 25
Intake manifold: 8; Oil pressure relief valve: 34
Exhaust manifold: 19; Sump, timing case and cover: 8
Water pump: 19; Starter motor: 40
Fan pulley: 7; Alternator 40 A to bracket: 61
Data provided as a guide — check against the workshop manual for your engine.
Head bolts: oil the threads. Tighten in stages from the centre outwards — refer to the workshop manual for the exact sequence.
Cylinder head gaskets
The DM950D uses gasket 11115-87812: https://www.compactmotorsport.com/product-page/daihatsu-dm950d-cylinder-head-gasket-11115-87812. The turbo DT and DTH use a graded gasket – the grade (thickness) is chosen to suit how far the pistons stand above the block. We stock grade 02: https://www.compactmotorsport.com/product-page/daihatsu-dm950dt-dth-cylinder-head-gasket-11115-87814-02 and grade 04: https://www.compactmotorsport.com/product-page/daihatsu-dm950dt-dth-cylinder-head-gasket-11115-87814-04. Replace like-for-like, or measure piston protrusion if the block or crank has been machined. Send your engine number and we'll help you choose.
Timing gears
With the crankshaft keyway at 12 o'clock, the idler gear marks line up with the crankshaft, camshaft and injection pump gear marks (11–1, 22–2, 33–3; later engines use letters AA–A, BB–B, CC–C). Gear backlash should not exceed 0.2 mm – replace worn gears as a set.
Injection pump timing (diesels)
Static timing is set by plunger lift at No. 1 TDC, measured with a dial gauge in place of the pump's distributor head screw.
DM950D (582447) — 0.81 ± 0.03 mm (later engines — early engines differ; send us your engine number)
DM950DTH (58A447) — 0.90 ± 0.03 mm
If you're replacing a DM950D pump (22100-87802) https://www.compactmotorsport.com/product-page/daihatsu-dm950d-injection-pump-assembly-22100-87802 or DM950DTH pump (22100-87811) https://www.compactmotorsport.com/product-page/daihatsu-dm950dth-injection-pump-assembly-22100-87811, match the ID code on the old pump's nameplate (9U1 or 9U4) – see How to identify your engine.
Belt-driven equipment
Use a spring-loaded idler to tension belts running off the front pulley. Fixed or screw-adjusted tensioners can easily be over-tightened, overloading the crankshaft and bearings.
Petrol models (DM950G / GH) – governor
If a petrol engine hunts: check the governor link sits close to the centre of the throttle lever hole at full throttle. If it still hunts, move the governor spring one hole further away from the lever pivot to make it less sensitive. To reset the governor, hold the control lever at full throttle, turn the governor shaft clockwise to its stop and tighten the lever nut to 10 Nm.
Daihatsu and Briggs & Stratton are trademarks of their respective owners; Compact Motorsport is an independent parts supplier.
Need parts or a second opinion? Email sales@compactmotorsport.com and send your engine number.

